Ang tanan nga mga Categories
EN

Panimalay>Balita>Dinamika sa industriya

Asembliya sa sleeve type pipe joint

Oras: 2022-06-08 Mga Hits: 22


(1) Pre-installed the most important link of the pre-installation of the sleeve type pipe haom direkta nga makaapekto sa pagkakasaligan sa selyo. Espesyal nga precursors kasagaran gikinahanglan.Mga kasangkapan nga adunay gamay nga diametro mahimo nga pre-nagtipon sa bangko vice. Ang espesipikong paagi mao ang paggamit sa a haom ingon nga ang matrix, ang nut, clamping sleeve mahimong pug-on sa tubo. Adunay nag-una nga tipo sa manggas pinaagi sa tubohaom, klase sa manggas matapos pinaagi sa pagkonektar sa ulo, tipo sa manggas nga tulo ka paagi nga tubo haomand other types. kini mao ang found that even for a batch of goods from the same manufacturer, the depth of the conical hole on thehaom is often not the same, resulting in leakage, and this problem is often ignored. The correct way is to use what kind of haom gigamit sa usa ka tumoy sa tubo, ug ang katugbang angay nga ikog is pre-installed with the same type of haom, so as to avoid leakage problems to the greatest extent. The end face of the pipe should be flush.

(2) After the pipe is sawed, it should be polished evenly on grinding wheel and other tools, and the burrs should be removed, cleaned and cleaned with high pressure air before use.

(3) Atol sa pre-instalar, ang coaxiality sa tubo ug ang haom should be kept as far as possible. If the pipe is too deviation, it will also cause sealing failure.

(4) The pre-installed force should not be too ambassador that the inner edge of the sleeve is just embedded in the outer wall of the pipe, and the sleeve should not be obvious deformation. When connecting pipes, assemble according to the specified tightening force. The clamping force of the 6-1 sleeve is 64-1 15N, 16ф MMR 259N, ф18mm for 450N. If the jacket deformation is serious in pre-installation, the sealing effect will be lost.

 

It is forbidden to add sealant and other fillers. Some people in order to achieve better sealing effect, in the card sleeve coated with sealant, the sealant was rushed into the hydraulic system, resulting in hydraulic components Yin nihole blockage and other faults.

 

(3) When connecting the pipe, the pipe should have enough deformation allowance to avoid the pipe being subjected to tensile force.

 

(four) When connecting the pipeline, it should avoid being subjected to lateral force, which will cause loose sealing if the lateral force is too large.

 

(five) when connecting the pipeline, it should be good once and avoid multiple disassembly, otherwise it will make the sealing performance worse.

 

Folding card sleeve type pipehaom instalar

(1) Ang pag-pickling sa mga tubo nga gikinahanglan sa Kapitulo 9 kinahanglang himoon una;

 

(2) Guntinga ang tubo sumala sa gikinahanglan nga gitas-on gamit ang sawing machine o espesyal nga pipe cutting machine ug uban pang mga himan, kini hingpit nga dili tugutan nga matunaw ang tubo (sama sa pagputol sa kalayo) o pagputol sa ligid sa paggaling; Kuhaa ang mga burr sa sulod ug sa gawas sa pipe end, metal chips ug hugaw; Kuhaa ang anti-rust agent ug hugaw sa tubohaom; Sa samang higayon aron sa pagsiguro sa roundness sa pipe;

 

(3) ang nut, ang manggas gibutang sa tubo, ang atubangang ngilit sa manggas (gamay nga tumoy) gikan sa tubo nga baba sa labing menos 3mm, ug unya ang tubo ngadto sa haomt body cone hole, top until;

 

(4) Hinay-hinay nga hugti ang nut, ibalik ang tubo hangtod nga dili na molihok, ug dayon hugti ang nut 2/3 hangtod 4/3 ka beses;

 

(5) Ablihi ug susiha kon ang dyaket naputol na ba sa tubo ug kon husto ba ang posisyon. Ang dyaket dili gitugotan nga adunay axial nga paglihok, apan gamay nga pagtuyok;

 

(6) Hupti ang nut pagkahuman sa pag-inspeksyon.